Do you have an ignition lock that needs to be rekeyed? Rekeying an ignition lock can seem like a daunting task, but it doesn’t have to be! In this blog post, we will provide simple steps on how to fix an ignition lock rekey. With just a few supplies and a little bit of time, you can easily rekey your ignition lock and have it working again in no time! So let’s get started!
Tools you will need
When it comes to fixing an ignition lock rekey, it’s important to have the right tools on hand. You will need a screwdriver and a pair of needle-nose pliers. In some cases, you may also need to get ignition lock replacement or ignition lockout services in order to gain access to the tumbler. It is important that you use the proper tools when working on the ignition system in order to avoid damaging any of the parts.
Remove the retaining clip.
The first step in fixing an ignition lock rekey is to remove the retaining clip. This is a small plastic piece located near the top of the ignition lock cylinder. It helps secure the tumblers in place. To remove the clip, you will need a pair of needle-nose pliers or a small flathead screwdriver. Simply insert either tool into the slot in the retaining clip and pull gently until the clip pops off. Once the clip is removed, you will be able to access the damaged tumbler inside the lock. If you are having trouble removing the clip, you may need to contact a professional ignition lock replacement or lockout service for assistance.
Take out the damaged tumbler.
Removing the damaged tumbler is a key step in replacing your ignition lock. First, use an appropriate tool, such as a flathead screwdriver, to lift the retaining clip that holds the tumbler in place. Once the retaining clip has been removed, you should be able to pull the old tumbler out of its slot. Be careful when doing this so that you don’t cause any further damage to the ignition lock. If you are having trouble getting the tumbler out, it may be time to call in a professional for ignition lockout services. This can help to ensure that the new tumbler is installed correctly and that your vehicle is secure.
Insert the new tumbler.
Once you have successfully removed the damaged tumbler from the ignition, it is time to insert the new one. To do this, you will need the replacement tumbler, which can be purchased at most automotive supply stores or online. Insert the tumbler into the slot that the previous one was in, and make sure it is lined up correctly. When properly installed, the tumbler should fit snugly in its slot and should not be able to move around. If you are having difficulty lining up the tumbler correctly, it is highly recommended that you contact an experienced locksmith or ignition lockout service provider for assistance. This will ensure that your ignition lock replacement is done correctly and without any further issues.
Reinstall the Retaining Clip
Now that the new tumbler has been inserted into the ignition lock, it’s time to replace the retaining clip. Take the new clip and slide it into place until you hear a click. Make sure that the clip is secured and fits snugly in the groove. This will ensure that your ignition lock rekey services is successful and secure.
If you need assistance replacing the retaining clip, please contact a professional Ignition Lockout service. An experienced locksmith can quickly assess the issue and get you back on the road safely. They can also provide advice on how to best maintain your ignition lock so that it stays in optimal condition.
Try out the New Tumbler
Before you finish your ignition lock rekey, it is important to test the new tumbler to ensure that it is working correctly. To do this, start by turning the key in the ignition until it clicks and holding it there. Then, turn the key slowly back and forth a few times, listening for any grinding or other strange noises. If you hear anything, then your new tumbler may not be properly installed, and you should repeat the process from Step 1 to check and make sure it is properly seated.
Once you are sure that everything is in place and secure, test the ignition lock with a key. Insert the new key into the ignition and turn it. If it turns without any difficulty, then your ignition lock rekey is complete, and your car should now start. If not, you may need to call an Ignition Lockout Services professional to come and take a look.
Contact us for Write With Us
Comments are closed.